通风管道会翘曲变形的原因是什么？

风道精代加工：为禁止排烟、甲烷气体等的元素被排污到户外去，基本上的壮况下都在设备开窗通风系统工作系统系统道道的，但正因为开窗通风系统工作系统系统道道大多都就是些碳素钢管、大跌岩的软件，在生产代加工和采用线程中习惯性显现出翘曲发生的疑问，介绍开窗通风系统工作系统系统道道会翘曲发生的理由，您晓得吗？下由安徽开窗通风系统工作系统系统道道精代加工生产厂安徽成路广开窗通风系统工作系统系统这里养大家分着来认识一下下。Air duct processing: In order to prevent substances such as oil fumes and gases from being discharged outdoors, ventilation ducts are usually installed. However, because ventilation ducts are mostly thin-walled and large undulating products, they often exhibit warping and deformation problems during production and use. Do you know the reasons for the warping and deformation of ventilation ducts? Below, let Jinan Chenglu Guangtongfeng, a ventilation duct processing manufacturer in Jinan, take you to learn more.镁水泥厂在大自然清理先决条件下其体型是一种个连续式胀大过程，其线胀大比率为0.1~0.2%，体型胀大率约为Magnesium cement undergoes a continuous expansion process in volume under natural curing conditions, with a linear expansion rate of 0.1~0.2% and a volume expansion rate of approximately菱镁矿在服烧历程中没法制止地时有发生部件过烧，使有一部电影件MgO呈死烧系统，过烧的MgO水化历程极慢，当已组合而成难度的混疑土石中的MgO再遇水后开始水化时，提取Mg(OH)2，密度胀大During the sintering process of magnesite, partial overburning is inevitable, resulting in a dead burning state of some MgO. The hydration process of overburned MgO is very slow. When MgO in the cement stone that has already formed strength is hydrated with water, it generates Mg (OH) 2, causing volume expansion轻烧钝化镁中下游离CaO水化时球体积太胀大90%，而卤影影片中发生着SO42-，当Ca(OH)2转成成石膏板时，液态球体积太将提升2倍以内，造成 包装材料断裂，这也是拘束轻烧钝化镁中下游离CaO含氧量、卤影影片中SO42-含氧量的的原因

During the hydration of free CaO in lightly burned magnesium oxide, the volume expands by 90%, while there is SO42- present in the brine sheet. When Ca (OH) 2 is converted into gypsum, the solid volume will increase by more than twice, causing deformation of the product. This is also the reason why the free CaO content in lightly burned magnesium oxide and the SO42- content in the brine sheet are constrainedMgO-Mg-C12-H2O采集体系水化应用程序就是个激列的热传递热议应用程序，而产于的线路重量又大，若条件摄氏度较高，则热议不断升温应用程序，板才机体摄氏度过高，热议不充足、，组成更大的结晶体弯曲应力应变和热胀大弯曲应力应变，使肉食品重量胀大。The hydration process of MgO-Mg-C12-H2O system is an intense exothermic reaction process, and the volume of the produced pipeline is large. If the ambient temperature is high, it will reflect the heating process. If the temperature of the board body is too high, the response is not sufficient, forming a large crystallization stress and thermal expansion stress, causing the volume of the product to expand.通风管线工作的设备按排在搭建物内时，应考虑搭建物混凝土楼板、梁的承担才会，需求分析时应该采用相关联依据。对於无尘室体系中的通风管线研制是指无尘室半封闭车间储存室所所制品或半所所制品。When arranging the air duct processing equipment inside the building, the load-bearing capacity of the building's floor slabs and beams should be considered, and corresponding methods should be adopted when needed. The manufacturing of air ducts for clean systems should have clean enclosed warehouses for storing products or semi-finished products.排烟通风管加工制作工艺产所应留有场地内容、成品或者半成品的运往k66凯时国际平台，排烟通风管加工制作工艺产所的选取不可阻饶消防栓k66凯时国际平台。大样图、安全体系图经检查顺应特殊要求，并举行了职业技能及交底。The air duct processing site should reserve transportation channels for on-site data, products, and semi-finished products, and the selection of air duct processing sites should not obstruct fire exits. The detailed drawings and system diagrams have been reviewed and found to meet the requirements, and skills and disclosures have been made.落水管加英语课外作业业网址应当存放建筑施工机具和知料沉积经营空间，仪器和电原应当最牢的护甲仪器。英语课外作业经营空间途中应疏通经络。需要有能满意度防火规范要求的种种用具及仪器。There should be a place for construction equipment and data storage in the air duct and operation site, and the equipment and power supply should have reliable protective equipment. The route to the workplace should be cleared. We need various instruments and equipment that can meet the fire protection requirements.排烟通排烟风管预设应该由独特的施工作业环境，环境应陡峭、拆洗，加工制作有效途径应刷平。双层铝箔纸绝热材料板排烟通排烟风管等另外的黏结知料排烟通排烟风管的环境应简单，应该由满不满意的纺织品沉积环境。The prefabrication of air ducts should have an independent workplace, which should be flat and clean, and the processing path should be leveled. The location of double-sided aluminum foil insulation board air ducts and other composite material air ducts should be monotonous, and there should be a satisfactory place for product stacking.

感谢您的阅读，此文的文章来源：山东通风管道加工更多的内容和问题请点击：//porn-k.com 我们会继续努力的为您提供服务，感谢您的支持！

Thank you for reading. The source of this article is Shandong Ventilation Pipeline Processing. For more information and questions, please click: //porn-k.com We will continue to work hard to provide you with services. Thank you for your support!

上一篇：纤维织物通风风管的施工方式
下一篇：白铁风管加工质量要注意哪些？